Skip to content

XACQUIRE_XRELEASE

Jump to bottom
Henk-Jan Lebbink edited this page Jun 6, 2018 · 15 revisions

XACQUIRE / XRELEASE — Hardware Lock Elision Prefix Hints

Opcode/Instruction 64/32bit Mode Support CPUID Feature Flag Description
F2 XACQUIRE V/V HLE A hint used with an “XACQUIRE-enabled“ instruction to start lock elision on the instruction memory operand address.
F3 XRELEASE V/V HLE A hint used with an “XRELEASE-enabled“ instruction to end lock elision on the instruction memory operand address.

NOTES:

  1. Software is not required to check the HLE feature flag to use XACQUIRE or XRELEASE, as they are treated as regular prefix if HLE feature flag reports 0.

Description

The XACQUIRE prefix is a hint to start lock elision on the memory address specified by the instruction and the XRELEASE prefix is a hint to end lock elision on the memory address specified by the instruction.

The XACQUIRE prefix hint can only be used with the following instructions (these instructions are also referred to as XACQUIRE-enabled when used with the XACQUIRE prefix):

  • Instructions with an explicit LOCK prefix (F0H) prepended to forms of the instruction where the destination operand is a memory operand: ADD, ADC, AND, BTC, BTR, BTS, CMPXCHG, CMPXCHG8B, DEC, INC, NEG, NOT, OR, SBB, SUB, XOR, XADD, and XCHG.

  • The XCHG instruction either with or without the presence of the LOCK prefix.

The XRELEASE prefix hint can only be used with the following instructions (also referred to as XRELEASE-enabled when used with the XRELEASE prefix):

  • Instructions with an explicit LOCK prefix (F0H) prepended to forms of the instruction where the destination operand is a memory operand: ADD, ADC, AND, BTC, BTR, BTS, CMPXCHG, CMPXCHG8B, DEC, INC, NEG, NOT, OR, SBB, SUB, XOR, XADD, and XCHG.

  • The XCHG instruction either with or without the presence of the LOCK prefix.

  • The “MOV mem, reg” (Opcode 88H/89H) and “MOV mem, imm” (Opcode C6H/C7H) instructions. In these cases, the XRELEASE is recognized without the presence of the LOCK prefix.

The lock variables must satisfy the guidelines described in Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 1, Section 16.3.3, for elision to be successful, otherwise an HLE abort may be signaled.

If an encoded byte sequence that meets XACQUIRE/XRELEASE requirements includes both prefixes, then the HLE semantic is determined by the prefix byte that is placed closest to the instruction opcode. For example, an F3F2C6 will not be treated as a XRELEASE-enabled instruction since the F2H (XACQUIRE) is closest to the instruction opcode C6. Similarly, an F2F3F0 prefixed instruction will be treated as a XRELEASE-enabled instruction since F3H (XRELEASE) is closest to the instruction opcode. Intel 64 and IA-32 Compatibility

The effect of the XACQUIRE/XRELEASE prefix hint is the same in non-64-bit modes and in 64-bit mode.

For instructions that do not support the XACQUIRE hint, the presence of the F2H prefix behaves the same way as prior hardware, according to

  • REPNE/REPNZ semantics for string instructions,

  • Serve as SIMD prefix for legacy SIMD instructions operating on XMM register

  • Cause #UD if prepending the VEX prefix.

  • Undefined for non-string instructions or other situations.

For instructions that do not support the XRELEASE hint, the presence of the F3H prefix behaves the same way as in prior hardware, according to

  • REP/REPE/REPZ semantics for string instructions,

  • Serve as SIMD prefix for legacy SIMD instructions operating on XMM register

  • Cause #UD if prepending the VEX prefix.

  • Undefined for non-string instructions or other situations.

Operation

XACQUIRE

IF XACQUIRE-enabled instruction
    THEN
        IF (HLE_NEST_COUNT < MAX_HLE_NEST_COUNT) THEN
            HLE_NEST_COUNT++
            IF (HLE_NEST_COUNT = 1) THEN
                HLE_ACTIVE ← 1
                IF 64-bit mode
                    THEN 
                        restartRIP ← instruction pointer of the XACQUIRE-enabled instruction
                    ELSE
                        restartEIP ← instruction pointer of the XACQUIRE-enabled instruction
                FI;
                Enter HLE Execution (* record register state, start tracking memory state *)
            FI; (* HLE_NEST_COUNT = 1*)
            IF ElisionBufferAvailable 
                THEN
                    Allocate elision buffer
                    Record address and data for forwarding and commit checking
                    Perform elision
                ELSE 
                    Perform lock acquire operation transactionally but without elision
            FI;
        ELSE (* HLE_NEST_COUNT = MAX_HLE_NEST_COUNT *)
                GOTO HLE_ABORT_PROCESSING
        FI;
    ELSE
        Treat instruction as non-XACQUIRE F2H prefixed legacy instruction
FI;

XRELEASE

IF XRELEASE-enabled instruction 
    THEN
        IF (HLE_NEST_COUNT > 0) 
            THEN
                HLE_NEST_COUNT--
                IF lock address matches in elision buffer THEN
                    IF lock satisfies address and value requirements THEN
                        Deallocate elision buffer
                    ELSE
                        GOTO HLE_ABORT_PROCESSING
                    FI;
                FI;
                IF (HLE_NEST_COUNT = 0) 
                    THEN
                        IF NoAllocatedElisionBuffer 
                            THEN
                            Try to commit transactional execution
                            IF fail to commit transactional execution 
                            THEN
                            GOTO HLE_ABORT_PROCESSING;
                            ELSE (* commit success *)
                            HLE_ACTIVE ← 0
                            FI;
                            ELSE
                            GOTO HLE_ABORT_PROCESSING
                        FI;
                FI;
        FI; (* HLE_NEST_COUNT > 0 *)
    ELSE 
        Treat instruction as non-XRELEASE F3H prefixed legacy instruction
FI;
(* For any HLE abort condition encountered during HLE execution *)
HLE_ABORT_PROCESSING:
  HLE_ACTIVE ← 0
    HLE_NEST_COUNT ← 0
    Restore architectural register state
    Discard memory updates performed in transaction
    Free any allocated lock elision buffers
    IF 64-bit mode
        THEN 
            RIP ← restartRIP
        ELSE
            EIP ← restartEIP
    FI;
    Execute and retire instruction at RIP (or EIP) and ignore any HLE hint
END

SIMD Floating-Point Exceptions

None

Other Exceptions

#GP(0) If the use of prefix causes instruction length to exceed 15 bytes.

Source: Intel® Architecture Software Developer's Manual (May 2018)
Generated: 5-6-2018

Clone this wiki locally