Integrated Release/1.14

.github/workflows/compile_nuttx.yml

@@ -45,6 +45,7 @@ jobs:
           matek_h743-slim,
           modalai_fc-v1,
           modalai_fc-v2,
+          mro_ctrl-zero-classic,
           mro_ctrl-zero-f7,
           mro_ctrl-zero-f7-oem,
           mro_ctrl-zero-h7,

ROMFS/px4fmu_common/init.d/rcS

@@ -183,7 +183,7 @@ else
 		param select-backup $PARAM_BACKUP_FILE
 	fi
 
-	if ver hwcmp PX4_FMU_V5X PX4_FMU_V6X ARK_FMU_V6X PX4_FMU_V6XRT
+	if mft query -q -k MFT -s MFT_ETHERNET -v 1
 	then
 		netman update -i eth0
 	fi
@@ -287,12 +287,9 @@ else
 		. $FCONFIG
 	fi
 
-	#
-	# Start IO for PWM output or RC input if enabled
-	#
-	if param compare -s SYS_USE_IO 1
+	if px4io supported
 	then
-		# Check if PX4IO present and update firmware if needed.
+	# Check if PX4IO present and update firmware if needed.
 		if [ -f $IOFW ]
 		then
 			if ! px4io checkcrc ${IOFW}
@@ -314,12 +311,12 @@ else
 					tune_control stop
 				fi
 			fi
-		fi
 
-		if ! px4io start
-		then
-			echo "PX4IO start failed"
-			set STARTUP_TUNE 2 # tune 2 = ERROR_TUNE
+			if ! px4io start
+			then
+				echo "PX4IO start failed"
+				set STARTUP_TUNE 2 # tune 2 = ERROR_TUNE
+			fi
 		fi
 	fi
 

boards/ark/fmu-v6x/init/rc.board_defaults

@@ -22,21 +22,14 @@ param set-default SENS_IMU_TEMP 10.0
 #param set-default SENS_IMU_TEMP_I 0.025
 #param set-default SENS_IMU_TEMP_P 1.0
 
-if ver hwtypecmp ARKV6X000000 ARKV6X001000 ARKV6X002000 ARKV6X003000 ARKV6X004000 ARKV6X005000 ARKV6X006000 ARKV6X007000
+if ver hwtypecmp ARKV6X000
 then
 	param set-default SENS_TEMP_ID 2818058
 fi
 
-if ver hwtypecmp ARKV6X000001 ARKV6X001001 ARKV6X002001 ARKV6X003001 ARKV6X004001 ARKV6X005001 ARKV6X006001 ARKV6X007001
+if ver hwtypecmp ARKV6X001
 then
 	param set-default SENS_TEMP_ID 3014666
 fi
 
-if ver hwtypecmp ARKV6X001000 ARKV6X001001 ARKV6X001002 ARKV6X001003 ARKV6X001004 ARKV6X001005 ARKV6X001006 ARKV6X001007
-then
-	param set-default SYS_USE_IO 0
-else
-	param set-default SYS_USE_IO 1
-fi
-
 safety_button start

boards/ark/fmu-v6x/init/rc.board_sensors

@@ -4,7 +4,7 @@
 #------------------------------------------------------------------------------
 set HAVE_PM2 yes
 
-if ver hwtypecmp ARKV6X005000 ARKV6X005001 ARKV6X005002 ARKV6X005003 ARKV6X005004
+if mft query -q -k MFT -s MFT_PM2 -v 0
 then
 	set HAVE_PM2 no
 fi
@@ -47,7 +47,7 @@ then
 	fi
 fi
 
-if ver hwtypecmp ARKV6X000000 ARKV6X001000 ARKV6X002000 ARKV6X003000 ARKV6X004000 ARKV6X005000 ARKV6X006000 ARKV6X007000
+if ver hwtypecmp ARKV6X000
 then
 	# Internal SPI bus IIM42652 with SPIX measured frequency of 32.051kHz
 	iim42652 -R 3 -s -b 1 -C 32051 start
@@ -59,7 +59,7 @@ then
 	icm42688p -R 6 -s -b 3 -C 32051 start
 fi
 
-if ver hwtypecmp ARKV6X000001 ARKV6X001001 ARKV6X002001 ARKV6X003001 ARKV6X004001 ARKV6X005001 ARKV6X006001 ARKV6X007001
+if ver hwtypecmp ARKV6X001
 then
 	# Internal SPI bus IIM42653 with SPIX measured frequency of 32.051kHz
 	iim42653 -R 3 -s -b 1 -C 32051 start

boards/ark/fmu-v6x/src/CMakeLists.txt

@@ -55,7 +55,6 @@ else()
 		init.c
 		led.c
 		mtd.cpp
-		manifest.c
 		sdio.c
 		spi.cpp
 		spix_sync.c

boards/ark/fmu-v6x/src/board_config.h

@@ -1,6 +1,6 @@
 /****************************************************************************
  *
- *   Copyright (c) 2016-2022 PX4 Development Team. All rights reserved.
+ *   Copyright (c) 2016-2024 PX4 Development Team. All rights reserved.
  *
  * Redistribution and use in source and binary forms, with or without
  * modification, are permitted provided that the following conditions
@@ -204,25 +204,17 @@
 #define BOARD_ADC_OPEN_CIRCUIT_V     (5.6f)
 
 /* HW Version and Revision drive signals Default to 1 to detect */
-#define BOARD_HAS_HW_VERSIONING // migrate to Split
+#define BOARD_HAS_HW_SPLIT_VERSIONING
 
 #define GPIO_HW_VER_REV_DRIVE  /* PG0 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTG|GPIO_PIN0)
 #define GPIO_HW_REV_SENSE      /* PH4 */  GPIO_ADC3_INP15
 #define GPIO_HW_VER_SENSE      /* PH3 */  GPIO_ADC3_INP14
 #define HW_INFO_INIT_PREFIX    "ARKV6X"
 
-#define BOARD_NUM_SPI_CFG_HW_VERSIONS 8 // Rev 0 and Rev 1
+#define BOARD_NUM_SPI_CFG_HW_VERSIONS 2
 //                 Base/FMUM
-#define ARKV6X00   HW_VER_REV(0x0,0x0) // ARKV6X,     Sensor Set  Rev 0
-#define ARKV6X01   HW_VER_REV(0x0,0x1) // ARKV6X,     Sensor Set  Rev 1
-//#define ARKV6X03   HW_VER_REV(0x0,0x3) // ARKV6X,     Sensor Set  Rev 3
-//#define ARKV6X04   HW_VER_REV(0x0,0x4) // ARKV6X,     Sensor Set  Rev 4
-#define ARKV6X10   HW_VER_REV(0x1,0x0) // NO PX4IO,   Sensor Set  Rev 0
-#define ARKV6X11   HW_VER_REV(0x1,0x1) // NO PX4IO,   Sensor Set  Rev 1
-#define ARKV6X40   HW_VER_REV(0x4,0x0) // ARKV6X,     Sensor Set  Rev 0   HB CM4 base Rev 3
-#define ARKV6X41   HW_VER_REV(0x4,0x1) // ARKV6X,     Sensor Set  Rev 1   HB CM4 base Rev 4
-#define ARKV6X50   HW_VER_REV(0x5,0x0) // ARKV6X,     Sensor Set  Rev 0   HB Mini Rev 5
-#define ARKV6X51   HW_VER_REV(0x5,0x1) // ARKV6X,     Sensor Set  Rev 1   HB Mini Rev 1 // never shipped
+#define ARKV6X_0   HW_FMUM_ID(0x0) // ARKV6X,     Sensor Set  Rev 0
+#define ARKV6X_1   HW_FMUM_ID(0x1) // ARKV6X,     Sensor Set  Rev 1
 
 #define UAVCAN_NUM_IFACES_RUNTIME  1
 
@@ -247,7 +239,6 @@
 /* PWM
  */
 #define DIRECT_PWM_OUTPUT_CHANNELS   8
-#define BOARD_PWM_FREQ	             1024000
 
 #define GPIO_FMU_CH1                    /* PI0  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN0)
 #define GPIO_FMU_CH2                    /* PH12 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTH|GPIO_PIN12)