Fix axis map on headtages that use PolledBno055

Directory.Build.props

@@ -13,7 +13,7 @@
     <PackageLicenseFile>LICENSE</PackageLicenseFile>
     <UseArtifactsOutput>true</UseArtifactsOutput>
     <PackageIcon>icon.png</PackageIcon>
-    <VersionPrefix>0.4.2</VersionPrefix>
+    <VersionPrefix>0.4.3</VersionPrefix>
     <VersionSuffix></VersionSuffix>
     <LangVersion>10.0</LangVersion>
     <Features>strict</Features>

OpenEphys.Onix1/Bno055DataFrame.cs

@@ -7,6 +7,19 @@ namespace OpenEphys.Onix1
     /// <summary>
     /// 3D-orientation data produced by a Bosch Bno55 9-axis inertial measurement unit (IMU).
     /// </summary>
+    /// <remarks>
+    /// The physical interpretation of the orientation measurements contained within a <see
+    /// cref="Bno055DataFrame"/> depends on the sensor fusion mode that is enabled and the axis configuration
+    /// that is chosen (see page. 26 of the <a
+    /// href="https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bno055-ds000.pdf">datasheet</a>)
+    /// . If the chip is in NDOF mode and is calibrated, orientation measurements (Quaternion, Euler Angles,
+    /// and Gravity Vector) are absolute ("allocentric") and referenced to the gravity vector and Earth's
+    /// magnetic field. Specifically, if the chip's axes are oriented such that Y points towords magnetic
+    /// north, X points towards magnetic east, and Z points opposite the gravity vector, the orientation
+    /// reading will be null (i.e. Quaternion: X = 0, Y = 0, Z = 0, W = 1; Euler Angles: Yaw = 0, Pitch = 0,
+    /// and Roll = 0 degrees; Gravity: X = 0, Y = 0, Z = 9.8 m/s^2). Linear acceleration readings are always
+    /// taken relative to the chip's axis definitions (they are "egocentric").
+    /// </remarks>
     public class Bno055DataFrame : DataFrame
     {
         /// <summary>

OpenEphys.Onix1/ConfigureNeuropixelsV1eHeadstage.cs

@@ -52,7 +52,7 @@ public ConfigureNeuropixelsV1eHeadstage()
         [TypeConverter(typeof(PolledBno055SingleDeviceFactoryConverter))]
         [Description("Specifies the configuration for the Bno055 device.")]
         public ConfigurePolledBno055 Bno055 { get; set; } =
-            new ConfigurePolledBno055 { AxisMap = Bno055AxisMap.ZXY, AxisSign = Bno055AxisSign.MirrorZ | Bno055AxisSign.MirrorY };
+            new ConfigurePolledBno055 { AxisMap = Bno055AxisMap.YZX, AxisSign = Bno055AxisSign.MirrorX | Bno055AxisSign.MirrorZ };
 
         /// <summary>
         /// Gets or sets the port.

OpenEphys.Onix1/ConfigureNeuropixelsV2eBetaHeadstage.cs

@@ -51,7 +51,7 @@ public ConfigureNeuropixelsV2eBetaHeadstage()
         [TypeConverter(typeof(PolledBno055SingleDeviceFactoryConverter))]
         [Description("Specifies the configuration for the Bno055 device.")]
         public ConfigurePolledBno055 Bno055 { get; set; } =
-            new ConfigurePolledBno055 { AxisMap = Bno055AxisMap.ZXY, AxisSign = Bno055AxisSign.Default };
+            new ConfigurePolledBno055 { AxisMap = Bno055AxisMap.YZX, AxisSign = Bno055AxisSign.MirrorX | Bno055AxisSign.MirrorY };
 
         /// <summary>
         /// Gets or sets the port.

OpenEphys.Onix1/ConfigureNeuropixelsV2eHeadstage.cs

@@ -51,7 +51,7 @@ public ConfigureNeuropixelsV2eHeadstage()
         [TypeConverter(typeof(PolledBno055SingleDeviceFactoryConverter))]
         [Description("Specifies the configuration for the Bno055 device.")]
         public ConfigurePolledBno055 Bno055 { get; set; } =
-            new ConfigurePolledBno055 { AxisMap = Bno055AxisMap.ZXY, AxisSign = Bno055AxisSign.Default };
+            new ConfigurePolledBno055 { AxisMap = Bno055AxisMap.YZX, AxisSign = Bno055AxisSign.MirrorX | Bno055AxisSign.MirrorY };
 
         /// <summary>
         /// Gets or sets the port.

OpenEphys.Onix1/ConfigurePolledBno055.cs

@@ -5,11 +5,14 @@
 namespace OpenEphys.Onix1
 {
     /// <summary>
-    /// Configures a Bosch Bno055 9-axis inertial measurement unit (IMU) that is polled by the host computer.
+    /// Configures a Bosch Bno055 9-axis inertial measurement unit (IMU) to operate in nine degrees of freedom
+    /// (NDOF) fusion mode that is polled by the host computer.
     /// </summary>
     /// <remarks>
-    /// This configuration operator can be linked to a data IO operator, such as <see
-    /// cref="PolledBno055Data"/>, using a shared <c>DeviceName</c>.
+    /// See page. 25 of the <a
+    /// href="https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bno055-ds000.pdf">datasheet</a>
+    /// for an explanation of NDOF mode. This configuration operator can be linked to a data IO operator,
+    /// such as <see cref="PolledBno055Data"/>, using a shared <c>DeviceName</c>.
     /// </remarks>
     [Editor("OpenEphys.Onix1.Design.PolledBno055Editor, OpenEphys.Onix1.Design", typeof(ComponentEditor))]
     [Description("Configures a PolledBno055 device.")]
@@ -150,38 +153,41 @@ public PolledBno055DeviceInfo(ContextTask context, Type deviceType, uint deviceA
 
     /// <summary>
     /// Specifies the axis map of a Bno055 compared to the default orientation.
-    /// the datasheet.
     /// </summary>
     /// <remarks>
-    /// The axis of the device can be reconfigured to the new reference axis to account for
-    /// differences in its mounting position. The following values can be applied to the Bno055's
-    /// AXIS_MAP_CONFIG register at address 0x41 in order to rotate the Bno055's coordinate system
-    /// compared to the default orientation presented on page 24 of the Bno055 datasheet.
+    /// The axes of the Bno055 can be reconfigured to account for differences in its mounting position. The
+    /// following values can be applied to the Bno055's AXIS_MAP_CONFIG register at address 0x41 to
+    /// rotate the Bno055's coordinate system compared to the default orientation presented on page 26 of the
+    /// Bno055 <a
+    /// href="https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bno055-ds000.pdf">datasheet</a>.
+    /// Remapping is documented using the following notion: <b>Original Axis->New Axis'</b>. For instance,
+    /// X->Z', indicates that what was the X-axis in the default configuration will be the Z axis in the remapped
+    /// configuration.
     /// </remarks>
     public enum Bno055AxisMap : uint
     {
         /// <summary>
-        /// Specifies X->X, Y->Y, Z->Z (chip default).
+        /// Specifies that X->X', Y->Y', Z->Z' (chip default). 
         /// </summary>
         XYZ = 0b00_10_01_00,
         /// <summary>
-        /// Specifies X->X, Y->Z, Z->Y.
+        /// Specifies that X->X', Z->Y', Y->Z'
         /// </summary>
         XZY = 0b00_01_10_00,
         /// <summary>
-        /// Specifies X->Y, Y->X, Z->Z.
+        /// Specifies that Y->X', X->Y', Z->Z'
         /// </summary>
         YXZ = 0b00_10_00_01,
         /// <summary>
-        /// Specifies X->Y, Y->Z, Z->X.
+        /// Specifies that Y->X', Z->Y', X->Z'
         /// </summary>
         YZX = 0b00_00_10_01,
         /// <summary>
-        /// Specifies X->Z, Y->X, Z->Y.
+        /// Specifies that Z->X', X->Y', Y->Z'
         /// </summary>
         ZXY = 0b00_01_00_10,
         /// <summary>
-        /// Specifies X->Z, Y->Y, Z->X.
+        /// Specifies that Z->X', Y->Y', X->Z'
         /// </summary>
         ZYX = 0b00_00_01_10,
     }
@@ -190,10 +196,17 @@ public enum Bno055AxisMap : uint
     /// Specifies the axis map sign of a Bno055 IMU
     /// </summary>
     /// <remarks>
-    /// The axis of the device can be reconfigured to the new reference axis to account for
-    /// differences in its mounting position. The following values can be applied to the Bno055's
-    /// AXIS_MAP_SIGN register at address 0x42 to mirror specific axes in the Bno055's coordinate
-    /// system compared to the default orientation presented on page 24 of the Bno055 datasheet.
+    /// <para>
+    /// The axes of the Bno055 can be reconfigured to account for differences in its mounting position. The
+    /// following values can be applied to the Bno055's AXIS_MAP_SIGN register at address 0x42 to mirror
+    /// specific axes in the Bno055's coordinate system compared to the default directions presented on page
+    /// 26 of the Bno055
+    /// <a href="https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bno055-ds000.pdf">datasheet</a>.
+    /// </para>
+    /// <para>
+    /// Note that this setting is applied after the axis map specified by <see cref="Bno055AxisMap"/> and
+    /// applies to the new axis definitions.
+    /// </para>
     /// </remarks>
     [Flags]
     public enum Bno055AxisSign : uint
@@ -203,15 +216,15 @@ public enum Bno055AxisSign : uint
         /// </summary>
         Default = 0b00000_000,
         /// <summary>
-        /// Specifies that Z axis should be mirrored.
+        /// Specifies that Z' axis should be mirrored.
         /// </summary>
         MirrorZ = 0b00000_001,
         /// <summary>
-        /// Specifies that Y axis should be mirrored.
+        /// Specifies that Y' axis should be mirrored.
         /// </summary>
         MirrorY = 0b00000_010,
         /// <summary>
-        /// Specifies that X axis should be mirrored.
+        /// Specifies that X' axis should be mirrored.
         /// </summary>
         MirrorX = 0b00000_100,
     }

OpenEphys.Onix1/ConfigureUclaMiniscopeV4.cs

@@ -50,8 +50,7 @@ public ConfigureUclaMiniscopeV4()
         [TypeConverter(typeof(PolledBno055SingleDeviceFactoryConverter))]
         [Description("Specifies the configuration for the Bno055 device.")]
         public ConfigurePolledBno055 Bno055 { get; set; } =
-            new ConfigurePolledBno055 { AxisMap = Bno055AxisMap.ZYX, AxisSign = Bno055AxisSign.MirrorX | Bno055AxisSign.MirrorY | Bno055AxisSign.MirrorZ };
-
+            new ConfigurePolledBno055 { AxisMap = Bno055AxisMap.ZYX, AxisSign = Bno055AxisSign.MirrorZ };
 
         /// <summary>
         /// Gets or sets the port.