Skip to content

Latest commit

 

History

History
186 lines (135 loc) · 5.32 KB

functionality.rst

File metadata and controls

186 lines (135 loc) · 5.32 KB

Functionality

This chapter will describe the features supported by VAB-600 Android evaluation image and how to evaluate these features.

Multimedia features

To evaluate the multimedia features, you can install the following APK from \EVK\tools\apks\.

  • Gallery2.apk: for video and photo playback
  • Music.apk: for audio playback

Network features

Configure the Settings->Ethernet in Android system to enable the VAB-600 on-board Ethernet function.

Miscellaneous features

Hiding system bar

When the application requires display of full screen, the system bar on the bottom area will be automatically hidden. For how to write an Android application that can display full screen, please refer to Android official website or the following website: http://blog.csdn.net/cjjky/article/details/6337172

ADB

VAB-600 Android BSP supports launching adb daemon when starting Android OS. Once the Android OS has completed booting and network is correctly configured, you can use adb to connect VAB-600, as mentioned in section 4.4.

USB device and SD card

SD card and USB devices including input devices (mouse and keyboard); as well as storage devices (flash or hard disk), are both supported.

Note

The BSP cannot identify more than one USB flash/hard disk.

SmartETK Features

SmartETK provides a set of APIs for the Android application to access the services provided by VAB-600 hardware. The SmartETK for VAB-600 supports the following features:

  • Watch Dog
  • RTC Power On
  • Programmable GPIO
  • Serial Ports

WatchDog: a timer helps the application/system to recover from dead circle or breakdown. When it is set, it will reboot the system if no “Feeding dog” signal is received.

RTC Power On: provides auto Power On feature by setting RTC auto wake up timer.

Programmable GPIO: provides high level interface for the applications to control the low level GPIO.

Serial Ports: provides serial port communication capability for Android applications.

All the features can be examined through the demo application SmartETK_sample.apk. The home UI of “SmartETK_sample.apk” is shown as :num:`Figure #figure-smartetk-sample`.

Smart ETK sample app screenshot

Smart ETK sample app screenshot

RTC Power On

Click "RTC" to enter its UI as shown in :num:`Figure #figure-rtc-example`. Follow the steps to test RTC function.

  1. Start "SmartETK sample"
  2. Enter the RTC page
  3. Set date, hour and minute
  4. Click "Set and Enable' button
  5. Turn off the system
  6. Wait for RTC auto boot

Note

  1. If wake-up time arrives at the same time when system is running, the system will automatically reboot. Please make sure the wakeup is disabled when the system is running.
  2. Please reset the wakeup time after you adjust the system time, date or timezone through Setting-> Date&Time. Otherwise, the system may be automatically waked up on an unexpected time.
Smart ETK RTC Power On example screenshot

Smart ETK RTC Power On example screenshot

WatchDog

Click "WatchDog" to enter its UI as shown in :num:`Figure #figure-watchdog-example`. Follow the steps to test WatchDog function.

  1. Start "SmartETK sample"
  2. Enter the Watch Dog page
  3. Set seconds (need to refresh in # seconds, otherwise the system will reboot)
  4. Click "Start" button
  5. Click "Refresh" to reset timer
  6. Wait for the system reboot
Smart ETK WatchDog example screenshot

Smart ETK WatchDog example screenshot

GPIO

Click "GPIO" to enter its UI as shown in :num:`Figure #figure-gpio-example`. Follow the steps to test GPIO function.

VAB-600 provides eight GPIO pins. Test GPIO function by using SmartETK_sample.apk.

There are two modes in the SamrtETK sample application.

  • Mode 1: pin 0 to pin 3 are GPO, pin 4 to pin 7 are GPI
  • Mode 2: pin 0 to pin 3 are GPI, pin 4 to pin 7 are GPO
  • Pull-Up: default GPI state is pull-up
  • Pull-Down: default GPI state is pull-down
  1. Start "SmartETK sample"
  2. Enter the GPIO page
  3. Click "Enable" button
  4. Switch between mode 1 and mode 2
  5. Change GPO switch to ensure GPI status is correct
Smart ETK GPIO On example screenshot

Smart ETK GPIO example screenshot

Serial Ports

Click "Serial Ports" to enter its UI as shown in :num:`Figure #figure-serial-example`. Follow the steps to test serial port function. VAB-600 supports UART 2 and external EXAR 4-channel USB to serial device.

Use SmartETK_sample.apk to test the UART function.

  1. Connect com port between VAB-600 and PC
  2. Open terminal on PC site and set baud rate as 115200
  3. Start "SmartETK sample"
  4. Enter the UART page
  5. Set dev note (ttyS2, ttyUSB0 ~ 3)
  6. Click "Connect" button
  7. Click "Disconnect" button
Smart ETK Serial Ports example screenshot

Smart ETK Serial Ports example screenshot