[BUG] no SD CARD ESP32

[Anion-anion]

luc Hi!
I am used ESP3d v 3.0 with SD card.

• MCU: ESP32
• Name: ESP32 Devkit v4
• Flash size: 4M

I connected the sd reader to the esp32 to contacts
CS D5
SCLK D17
MISO D19
MOSI D23

the configuration of the ESP3D is as follows. But he doesn't see the sd card. Writes NO SD CARD
luc, what am I doing wrong?

---

[ESP780]/SD
Directory on Global FS : /SD
0 file, 0 dir
Total 0 B, Used 0 B, Available: 0 B
[ESP780]/SD
Directory on Global FS : /SD
0 file, 0 dir
Total 0 B, Used 0 B, Available: 0 B
[ESP790]
Incorrect command!
[ESP790]/SD
Incorrect command!
[ESP780]
Directory on Global FS : /

FS SD 0 B 2021-11-09 00:00:41 1 file, 1 dir > [ESP200] No SD card > ESP700 > [ESP700] ok > [ESP715]FORMATSD Start Formating ------

terminal send:
error: No SD card
E (1124403) sdmmc_common: sdmmc_init_ocr: send_op_cond (1) returned 0x107

config.h - ESP3D configuration file

Copyright (c) 2014 Luc Lebosse. All rights reserved.

This code is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.

This code is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public
License along with This code; if not, write to the Free Software
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#ifndef _CONFIGURATION_H
#define _CONFIGURATION_H

//FEATURES - comment to disable //////////////////////////////////////////////////////////

//WiFi setup station as default, use AP mode first if not done
//Note: need both defined to enable it
//#define STATION_WIFI_SSID ""
//#define STATION_WIFI_PASSWORD ""
//you can also use a different config file for SSID/password
//this file is ignored by github
#if defined __has_include

if __has_include ("myconfig.h")

include "myconfig.h"

endif

#endif

//SERIAL_COMMAND_FEATURE: allow to send command by serial
#define SERIAL_COMMAND_FEATURE

//AUTHENTICATION_FEATURE: protect pages by login password
//#define AUTHENTICATION_FEATURE

//WIFI_FEATURE : enable WIFI function
#define WIFI_FEATURE

//ETH_FEATURE : enable Ethernet function
//#define ETH_FEATURE

//BLUETOOTH_FEATURE : enable BT Serial function
//#define BLUETOOTH_FEATURE

//HTTP_FEATURE : enable HTTP function
#define HTTP_FEATURE

//TELNET_FEATURE : enable Telnet function
#define TELNET_FEATURE

//WS_DATA_FEATURE: allow to connect serial from Websocket
#define WS_DATA_FEATURE

//DISPLAY_DEVICE: allow screen output
//OLED_I2C_SSD1306 1
//OLED_I2C_SSDSH1106 2
//TFT_SPI_ILI9341_320X240 3
//TFT_SPI_ILI9488_480X320 4
//#define DISPLAY_DEVICE TFT_SPI_ILI9488_480X320

//UI_TYPE_BASIC 1
//UI_TYPE_ADVANCED 2
//#define DISPLAY_UI_TYPE UI_TYPE_ADVANCED

//UI_COLORED 1
//UI_MONOCHROME 2
//#define DISPLAY_UI_COLOR UI_COLORED

//BUZZER_DEVICE: allow to connect passive buzzer
//#define BUZZER_DEVICE

#if defined (DISPLAY_DEVICE)
//for ILI9143 edit User_Setup.h of TFT_eSPI library
#if (DISPLAY_DEVICE == OLED_I2C_SSD1306) || (DISPLAY_DEVICE == OLED_I2C_SSDSH1106)
//#define DISPLAY_I2C_PIN_RST 16 //comment if not applicable
//#define DISPLAY_I2C_ADDR 0x3c
#endif //(DISPLAY_DEVICE == OLED_I2C_SSD1306) || (DISPLAY_DEVICE == OLED_I2C_SSDSH1106)
//#define DISPLAY_FLIP_VERTICALY 1 //comment to disable
#if (DISPLAY_DEVICE == TFT_SPI_ILI9341_320X240) || (DISPLAY_DEVICE == TFT_SPI_ILI9488_480X320)
//#define DISPLAY_TOUCH_DRIVER XPT2046_SPI
//#define DISPLAY_LED_PIN 27 //-1 if none
#endif //(DISPLAY_DEVICE == TFT_SPI_ILI9341_320X240) || (DISPLAY_DEVICE == TFT_SPI_ILI9488_480X320)
#endif //DISPLAY_DEVICE

//INPUT_DEVICE: allow input
//ROTARY_ENCODER 1
//#define INPUT_DEVICE ROTARY_ENCODER

//SENSOR_DEVICE: send info based on defined sensor
//DHT11_DEVICE 1
//DHT22_DEVICE 2
//ANALOG_DEVICE 3
//BMP280_DEVICE 4
//BME280_DEVICE 5
//#define SENSOR_DEVICE BMP280_DEVICE

#ifdef BUZZER_DEVICE
#define ESP3D_BUZZER_PIN 15
#endif //BUZZER_DEVICE

#ifdef SENSOR_DEVICE
//pin
#define ESP3D_SENSOR_PIN 22
#define SENSOR_ADDR 0x76
//Conversion coefficient
#define SENSOR_CONVERTER(v) v*0.588
//Unit to use, if not applicaple for sensor will use default one
//it is used also for the output format
//C for Celsius / F for Fahrenheit / V for volt
#define SENSOR__UNIT "C"
#endif //SENSOR_DEVICE

//PIN_RESET_FEATURE : allow to reset settings by setting low a pin
#define PIN_RESET_FEATURE
#if defined (PIN_RESET_FEATURE)
#define ESP3D_RESET_PIN 2
#endif //PIN_RESET_FEATURE

//SD_DEVICE: to access SD Card files directly instead of access by serial using printer Board FW
//ESP_SD_NATIVE 1 //esp32 / esp8266
//ESP_SDIO 2 //esp32 only
//ESP_SDFAT 3 //esp8266 (same as native) / esp32
#define SD_DEVICE ESP_SDIO //ESP_SDFAT

//SDIO mode
#define SD_ONE_BIT_MODE true

//SD Device Connection type (default is direct)
//ESP_DIRECT_SD
//ESP_SHARED_SD
#define SD_DEVICE_CONNECTION ESP_DIRECT_SD

//pin if reader has insert detection feature
//let -1 or comment if none
#define ESP_SD_DETECT_PIN -1
//value expected for ESP_SD_DETECT_PIN
#define ESP_SD_DETECT_VALUE 1

//FILESYSTEM_FEATURE: to host some files on flash
//ESP_SPIFFS_FILESYSTEM 0
//ESP_FAT_FILESYSTEM 1
//ESP_LITTLEFS_FILESYSTEM 2
#define FILESYSTEM_FEATURE ESP_SPIFFS_FILESYSTEM

//Allows to mount /FS and /SD under / for FTP server
#define GLOBAL_FILESYSTEM_FEATURE

//FTP_FEATURE : enable FTP feature
//FS_ROOT mount all FS
//FS_FLASH mount Flash FS
//FS_SD mount SD FS
//FS_USBDISK mount USB disk FS
#define FTP_FEATURE FS_ROOT

//DIRECT_PIN_FEATURE: allow to access pin using ESP201 command
#define DIRECT_PIN_FEATURE

//TIMESTAMP_FEATURE: set time system
#define TIMESTAMP_FEATURE

//FILESYSTEM_TIMESTAMP_FEATURE: display last write time from Flash files
#define FILESYSTEM_TIMESTAMP_FEATURE

//FILESYSTEM_TIMESTAMP_FEATURE:display last write time from SD files
//#define SD_TIMESTAMP_FEATURE

//MDNS_FEATURE: this feature allow type the name defined
//in web browser by default: http:\esp8266.local and connect
//need bonjour protocol on windows
#define MDNS_FEATURE

//SSDP_FEATURE: this feature is a discovery protocol, supported on Windows out of the box
#define SSDP_FEATURE

//CAPTIVE_PORTAL_FEATURE: In SoftAP redirect all unknow call to main page
#define CAPTIVE_PORTAL_FEATURE

//OTA_FEATURE: this feature is arduino update over the air
//#define OTA_FEATURE

//WEB_UPDATE_FEATURE: allow to flash fw using web UI
#define WEB_UPDATE_FEATURE

//NOTIFICATION_FEATURE : allow to push notifications
#define NOTIFICATION_FEATURE

//For ESP8266 Only, it define which secure client to use AXTls or BearSSL
//#define USING_AXTLS

//if not using AXTLS need to decrease size of packet to not be OOM
#define BEARSSL_MFLN_SIZE 512
#define BEARSSL_MFLN_SIZE_FALLBACK 4096

//CAMERA_DEVICE: Enable the support of connected camera
//CAMERA_MODEL_CUSTOM 0 //Edit the pins in include/pins.h
//CAMERA_MODEL_ESP_EYE 1
//CAMERA_MODEL_M5STACK_PSRAM 2
//CAMERA_MODEL_M5STACK_WIDE 3
//CAMERA_MODEL_AI_THINKER 4 e.g. used by ESP32-CAM
//CAMERA_MODEL_WROVER_KIT 5
//#define CAMERA_DEVICE CAMERA_MODEL_AI_THINKER
//#define CAMERA_DEVICE_FLIP_VERTICALY //comment to disable
//#define CAMERA_DEVICE_FLIP_HORIZONTALY//comment to disable
//#define CUSTOM_CAMERA_NAME "ESP32-CAM"

//Allow remote access by enabling cross origin access
//check https://developer.mozilla.org/en-US/docs/Web/HTTP/CORS
//this should be enabled only in specific cases
//like show the camera in web page different than device web server
//if you do not know what is that then better left it commented
//#define ESP_ACCESS_CONTROL_ALLOW_ORIGIN

//ESP_GCODE_HOST_FEATURE : allow to send GCODE with ack
#define ESP_GCODE_HOST_FEATURE

//ESP_AUTOSTART_SCRIPT : to do some actions / send GCODE at start, need ESP_GCODE_HOST_FEATURE enabled
//can be a line od several GCODES separated by \n e.g. "M21\nM117 SD mounted\n"
//can be a file name, if exists, commands inside will be processed, e.g "/FS:/autostart.esp"
//#define ESP_AUTOSTART_SCRIPT "M117 Mouning SD\nM21\n"

//ESP_LUA_INTERPRETER_FEATURE : add lua scripting feature
//#define ESP_LUA_INTERPRETER_FEATURE

//Extra features /////////////////////////////////////////////////////////////////////////
/************************************
*

• DEBUG
• **********************************/
  //Do not do this when connected to printer !!!
  //be noted all upload may failed if enabled
  //DEBUG_OUTPUT_SERIAL0 1
  //DEBUG_OUTPUT_SERIAL1 2
  //DEBUG_OUTPUT_SERIAL2 3
  //DEBUG_OUTPUT_TELNET 4
  //DEBUG_OUTPUT_WEBSOCKET 5
  //#define ESP_DEBUG_FEATURE DEBUG_OUTPUT_SERIAL0

#ifdef ESP_DEBUG_FEATURE
#define DEBUG_ESP3D_OUTPUT_PORT 8000
#endif //ESP_DEBUG_FEATURE

#if defined (DISPLAY_DEVICE) && (DISPLAY_UI_TYPE == UI_TYPE_ADVANCED)
//allows to use [ESP216]SNAP to do screen capture
#define DISPLAY_SNAPSHOT_FEATURE
#define AUTO_SNAPSHOT_FEATURE
#endif //DISPLAY_DEVICE

/************************************
*

• Serial Communications
• **********************************/
  //which serial ESP use to communicate to printer (ESP32 has 3 serials available, ESP8266 only 2)
  //USE_SERIAL_0 for ESP8266/32
  //USE_SERIAL_1 for ESP8266/32
  //USE_SERIAL_2 for ESP32 Only
  #define ESP_SERIAL_OUTPUT USE_SERIAL_0

//Serial rx buffer size is 256 but can be extended
#define SERIAL_RX_BUFFER_SIZE 512

/************************************
*

• Settings
• **********************************/
  //SETTINGS_IN_EEPROM 0
  //SETTINGS_IN_PREFERENCES 1
  #define ESP_SAVE_SETTINGS SETTINGS_IN_EEPROM

/************************************
*

• Customize ESP3D
• **********************************/
  #if defined( ARDUINO_ARCH_ESP8266)
  #define ESP_MODEL_NAME "ESP8266"
  #define ESP_MODEL_URL "http://espressif.com/en/products/esp8266/"
  #endif //ARDUINO_ARCH_ESP8266
  #if defined( ARDUINO_ARCH_ESP32)
  #define ESP_MODEL_NAME "ESP32"
  #define ESP_MODEL_URL "https://www.espressif.com/en/products/hardware/esp-wroom-32/overview"
  #endif //ARDUINO_ARCH_ESP32
  #define ESP_MODEL_NUMBER "ESP3D 3.0"
  #define ESP_MANUFACTURER_NAME "Espressif Systems"
  #define ESP_MANUFACTURER_URL "http://espressif.com"

#define NOTIFICATION_ESP_ONLINE "Hi, %ESP_NAME% is now online at %ESP_IP%"
#define ESP_NOTIFICATION_TITLE "ESP3D Notification"

#endif //_CONFIGURATION_H

[github-actions[bot]]

Thank your for submiting, please be sure you followed template or your issue may be dismissed. if you deleted the template it is here

[luc-github]

#define SD_DEVICE ESP_SDIO //ESP_SDFAT is incorrect you use SPI pins so you must use spi
#define SD_DEVICE ESP_SD_NATIVE is the proper setting

[Anion-anion]

Thanks Luс!
it works!
I`am Happy)

[Anion-anion]

Luс!
how to increase the speed of the sd card. Now an 8 MB file is copied for about 7 minutes - it's a long, long time. Is there a way to speed up writing and reading from the sd card by ftp?

[Legsmaniac]

@Anion-anion https://blog.prusaprinters.org/easy-wireless-printing-with-flashair-sd-cards_8603/

[luc-github]

@Anion-anion the esp32 webserver is not really fast at the moment
to speed upload use webdav instead and sdio for SDCard instead of SPI and may be do some tuning : #491 (comment)

But what do you want to do with files uploaded on SDCard connected to ESP32 ? the printer cannot see it, so may I know the purpose to have fast upload on SD ?