forked from mtakala/megaprinter_tempdriver
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathSI2CIO.h
149 lines (126 loc) · 5 KB
/
SI2CIO.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
// ---------------------------------------------------------------------------
// Created by Francisco Malpartida on 20/08/11.
// Copyright 2011 - Under creative commons license 3.0:
// Attribution-ShareAlike CC BY-SA
//
// This software is furnished "as is", without technical support, and with no
// warranty, express or implied, as to its usefulness for any purpose.
//
// Thread Safe: No
// Extendable: Yes
//
// @file SI2CIO.h
// This file implements a basic IO library using the PCF8574 I2C IO Expander
// chip, but using software I2C.
//
// @brief
// Implement a basic IO library to drive the PCF8574* I2C IO Expander ASIC.
// The library implements basic IO general methods to configure IO pin direction
// read and write uint8_t operations and basic pin level routines to set or read
// a particular IO port.
//
// @version API 1.0.0
//
// @author F. Malpartida - [email protected]
// Adapted to SoftIC2 by Adrian Piccioli - [email protected]
// ---------------------------------------------------------------------------
#ifndef _SI2CIO_H_
#define _SI2CIO_H_
#include <inttypes.h>
#define _SI2CIO_VERSION "1.0.0"
/*!
@class
@abstract SI2CIO
@discussion Library driver to control PCF8574 based ASICs. Implementing
library calls to set/get port through I2C bus.
*/
class SI2CIO
{
public:
/*!
@method
@abstract Constructor method
@discussion Class constructor constructor.
*/
SI2CIO ( );
/*!
@method
@abstract Initializes the device.
@discussion This method initializes the device allocating an I2C address.
This method is the first method that should be call prior to calling any
other method form this class. On initialization all pins are configured
as INPUT on the device.
@param i2cAddr: I2C Address where the device is located.
@result 1 if the device was initialized correctly, 0 otherwise
*/
int begin ( uint8_t i2cAddr );
/*!
@method
@abstract Sets the mode of a particular pin.
@discussion Sets the mode of a particular pin to INPUT, OUTPUT. digitalWrite
has no effect on pins which are not declared as output.
@param pin[in] Pin from the I2C IO expander to be configured. Range 0..7
@param dir[in] Pin direction (INPUT, OUTPUT).
*/
void pinMode ( uint8_t pin, uint8_t dir );
/*!
@method
@abstract Sets all the pins of the device in a particular direction.
@discussion This method sets all the pins of the device in a particular
direction. This method is useful to set all the pins of the device to be
either inputs or outputs.
@param dir[in] Direction of all the pins of the device (INPUT, OUTPUT).
*/
void portMode ( uint8_t dir );
/*!
@method
@abstract Reads all the pins of the device that are configured as INPUT.
@discussion Reads from the device the status of the pins that are configured
as INPUT. During initialization all pins are configured as INPUTs by default.
Please refer to pinMode or portMode.
@param none
*/
uint8_t read ( void );
/*!
@method
@abstract Read a pin from the device.
@discussion Reads a particular pin from the device. To read a particular
pin it has to be configured as INPUT. During initialization all pins are
configured as INPUTs by default. Please refer to pinMode or portMode.
@param pin[in] Pin from the port to read its status. Range (0..7)
@result Returns the pin status (HIGH, LOW) if the pin is configured
as an output, reading its value will always return LOW regardless of its
real state.
*/
uint8_t digitalRead ( uint8_t pin );
/*!
@method
@abstract Write a value to the device.
@discussion Writes to a set of pins in the device. The value is the binary
representation of all the pins in device. The value written is masked with
the configuration of the direction of the pins; to change the state of
a particular pin with this method, such pin has to be configured as OUTPUT
using the portMode or pinMode methods. If no pins have been configured as
OUTPUTs this method will have no effect.
@param value[in] value to be written to the device.
@result 1 on success, 0 otherwise
*/
int write ( uint8_t value );
/*!
@method
@abstract Writes a digital level to a particular pin.
@discussion Write a level to the indicated pin of the device. For this
method to have effect, the pin has to be configured as OUTPUT using the
pinMode or portMode methods.
@param pin[in] device pin to change level. Range (0..7).
@para level[in] logic level to set the pin at (HIGH, LOW).
@result 1 on success, 0 otherwise.
*/
int digitalWrite ( uint8_t pin, uint8_t level );
private:
uint8_t _shadow; // Shadow output
uint8_t _dirMask; // Direction mask
uint8_t _i2cAddr; // I2C address
bool _initialised; // Initialised object
};
#endif