-
Notifications
You must be signed in to change notification settings - Fork 4
/
Copy pathauto-z.cfg
147 lines (147 loc) · 7.73 KB
/
auto-z.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
[z_calibration]
probe_nozzle_x: 230.0
probe_nozzle_y: 357.0
# The X and Y coordinates (in mm) for clicking the nozzle on the
# Z endstop.
probe_switch_x: 226.0
probe_switch_y: 337.5
# The X and Y coordinates (in mm) for clicking the probe's switch
# on the Z endstop.
#probe_bed_x: default from relative_reference_index of bed_mesh
#probe_bed_y: default from relative_reference_index of bed_mesh
# The X and Y coordinates (in mm) for probing on the print surface
# (e.g. the center point) These coordinates will be adapted by the
# probe's X and Y offsets. The default is the relative_reference_index
# of the configured bed_mesh. It will raise an error if there is no
# probe_bed site and no bed_mesh with a relative_reference_index
# configured.
#switch_offset: 0.42 # Standard value, too low
#switch_offset: 0.32 # First guess, too high
#switch_offset: 0.35 # Just a tiny bit of elephants foot
#switch_offset: 0.36 # But this one has some sausage areas... but I didn't soak soaking made it worse
#switch_offset: 0.35 # I can feel the edges, and Three Spiral Christmas Balls detached.
#switch_offset: 0.34 # First layer miced at 0.29mm also, it seems I forgot that lower this raises the nozzle.
#switch_offset: 0.40 # A bit of fading here...
#switch_offset: 0.39 # First layer stringy, go back to a bit of fading...
#switch_offset: 0.40 # Some elephants foot, clear oversquish
#switch_offset: 0.39 # Fading in a few areas, appears to have marked the PEI a bit
#switch_offset: 0.38 # Fading and slightly marginal, could be the filament though.
#switch_offset: 0.28 # Skirt was only 0.14mm thick!
#switch_offset: 0.14 # Brim was 0.225 thick...
#switch_offset: 0.17 # Going to give it a bit more... we had a detachement
#switch_offset: 0.19 # Now that auto-Z is fixed for print area mesh, it seems a bit high again...
#switch_offset: 0.21 # Detach and a bit sausagy... what's going on here?
#switch_offset: 0.21 # Skirt now at 0.24mm
#switch_offset: 0.25 # A bit over-squished
#switch_offset: 0.24 # Almost there...
#switch_offset: 0.23 # Some flow patches good, some bad...
#switch_offset: 0.22 # Getting marginally too high now. :(
#---- Haldis ----
#switch_offset: 0.24 # Still just a tiny bit too low...
#switch_offset: 0.26 # After swap to rapido, this is too low by a fair bit..
#
# This is good for the V6 hotend, but no damn good for the Dragon...
#switch_offset: 0.37 # With SB/CW2, *WAY* too low... complete squish, no lines.
#switch_offset: 0.32 # Still way too low... no lines, clear gouging
#switch_offset: 0.28 # We're in the right ballpark now, but still a bit low...
#switch_offset: 0.27 # And still too low...
#switch_offset: 0.25
#---- Rapido
#switch_offset: 0.26 # After swap to rapido, this is too low by a fair bit..
#switch_offset: 0.24 # Now too high...
#switch_offset: 0.25 # Still a bit high
#switch_offset: 0.26 # At the corners, way too high.
#switch_offset: 0.30 # At least things stuck, but still too high
#switch_offset: 0.32 # Still textured lines across most of the bed
#switch_offset: 0.34 # "The Incident" after that, *way* too high
#=====
#switch_offset: 0.5 # Just a tiny bit too low... elephants feet most places
#switch_offset: 0.46 # Too low again, but not a whole lot...
#switch_offset: 0.45 # 0.01 ain't nothing.
#switch_offset: 0.44 # Still just a touch too low...
#switch_offset: 0.43 # Starting to actually see separation on some bottoms... not good.
#switch_offset: 0.44
#switch_offset: 0.45
#switch_offset: 0.46 # Perfect for smooth PEI, not for textured
#switch_offset: 0.48 # Perfect for textured PEI, not for smooth
#switch_offset: 0.08 # Perfect for PEX with circles
#switch_offset: 0.48 # Just a bit high...
#switch_offset: 0.50 # Perfect for PEX with cat but
#switch_offset: 3.42 # Way too low now that the ooze on probe is fixed. :(
#switch_offset: 3.22 # But this is (obviously) too high.
#switch_offset: 3.29 # VH6Box power bottom is clearly printed too high
#switch_offset: 3.32 # Still too high
#switch_offset: 3.38 # Better, but not quite
#switch_offset: 3.40 #
#---- DropEffects XG
# Started at 3.40, but that dragged (but didn't actually gouge) the surface.
#switch_offset: 3.18 # With 3DXTech gold, just *barely* didn't drag
#switch_offset: 3.08 # No, I guess I misread that... this was all sausage and the last was just a bit sausage
#switch_offset: 3.23 # 3DXTech Gold was wet and silly... with BuMat, this is too high
#switch_offset: 3.30 # Better, but still a bit low...
#switch_offset: 3.35 # Detached purple dragon. :( Just a bit of open though, so close...
#switch_offset: 3.40 # Absolutely too low. Green dragon first layer was dredged all over the bed.
#switch_offset: 3.37 # Still dredging...
switch_offset: 3.35
#=====
# The trigger point offset of the used mag-probe switch.
# This needs to be fined out manually. More on this later
# in this section..
# Klicky
#max_deviation: 1.0
# Unklicky
max_deviation: 3.5
# The maximum allowed deviation of the calculated offset.
# If the offset exceeds this value, it will stop!
# The default is 1.0 mm.
#samples: default from "probe:samples" section
# The number of times to probe each point. The probed z-values
# will be averaged. The default is from the probe's configuration.
#samples_tolerance: default from "probe:samples_tolerance" section
# The maximum Z distance (in mm) that a sample may differ from other
# samples. The default is from the probe's configuration.
#samples_tolerance_retries: default from "probe:samples_tolerance_retries" section
# The number of times to retry if a sample is found that exceeds
# samples_tolerance. The default is from the probe's configuration.
#samples_result: default from "probe:samples_result" section
# The calculation method when sampling more than once - either
# "median" or "average". The default is from the probe's configuration.
clearance: 16.0
# The distance in mm to move up before moving to the next
# position. The default is two times the z_offset from the probe's
# configuration.
#position_min: 0.0
# Minimum valid distance (in mm) used for probing move. The
# default is from the Z rail configuration.
speed: 100.0
# The moving speed in X and Y. The default is 50 mm/s.
#lift_speed: default from "probe:lift_speed" section
# Speed (in mm/s) of the Z axis when lifting the probe between
# samples and clearance moves. The default is from the probe's
# configuration.
#probing_speed: default from "stepper_z:homing_speed" section.
# The fast probing speed (in mm/s) used, when probing_first_fast
# is activated. The default is from the Z rail configuration.
#probing_second_speed: default from "stepper_z:second_homing_speed" section.
# The slower speed (in mm/s) for probing the recorded samples.
# The default is second_homing_speed of the Z rail configuration.
#probing_retract_dist: default from "stepper_z:homing_retract_dist" section.
# Distance to backoff (in mm) before probing the next sample.
# The default is homing_retract_dist from the Z rail configuration.
probing_first_fast: true
# If true, the first probing is done faster by the probing speed.
# This is to get faster down and the result is not recorded as a
# probing sample. The default is false.
start_gcode: Dock_Probe_Unlock
# A list of G-Code commands to execute prior to each calibration command.
# See docs/Command_Templates.md for G-Code format. This can be used to
# attach the probe.
before_switch_gcode: Attach_Probe
# A list of G-Code commands to execute prior to each probing on the
# mag-probe. See docs/Command_Templates.md for G-Code format. This can be
# used to attach the probe after probing on the nozzle and before probing
# on the mag-probe.
end_gcode: Dock_Probe
# A list of G-Code commands to execute after each calibration command.
# See docs/Command_Templates.md for G-Code format. This can be used to
# detach the probe afterwards.